Search site

Contact

Car diagnostic tools information by obd2tool

https://www.obd2tool.com

Welcome to my blog,here some auto diagnostic tools will be displayed. If you want to know more information,you can visit our official website: www.obd2tool.com.

lovelily750@gmail.com

News

Visitors notice

12/01/2014 07:47
Let your visitors know about news and events on your website as often as possible. You need to keep your website up-to-date so that your visitors will get used to visiting your pages regularly. You can use RSS feeds to deliver new articles directly to your readers.

Website launched

12/01/2014 07:46
Our new website has been launched today. Tell your visitors why you have started a new presentation and how it benefits them. Mention your goals and project advantages. Try to briefly give your visitors reasons why they should return to your pages.

The blog of OBD2 TOOL

How to Configure WiFi and USB for Original JLR DoIP VCI

03/28/2021 17:08
Part 1: How to Configure WiFi for Original JLR DoIP VCI /setup wireless connection? Original Jaguar Land Rover diagnostic tool JLR DoiP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting. Procedure: Connect JLR DoiP VCI W-F interface with...

How to Restore X431 V X-431 Pro to Factory Settings

03/12/2021 17:34
How to Restore X431 V X-431 Pro to Factory Settings ? Read this before operation: 1. The following method does not apply to X431 V+ and X431 Pro3 2. Please use this function carefully, improper operation may cause the dead of X431 V, besides, after the factory settings are restored, all user...

How to Use HP Tuners vs. Y2K Silverado LM7 & TSP Peformance Cam

03/05/2021 10:08
To begin this HP Tuners Thread… The FIRST Place I went directly to was THIS Site: HPTuners – Connect > Read > Edit > Write > Drive HP Tuners, the home of VCM Suite and the MPVI since 2003. Now enhancing these to new heights with a new feature rich VCM Editor and VCM Scanner, coupled...

How to Use Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007

02/20/2021 18:27
I am gonna use the new tool Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007. The scanner just came to me last week. Xhorse VVDI Key Tool Plus supports DOIP/CAN-FD/ CAN and K protocol switch pin/Chip pin detection/Toyota smart key programming without simulator/Long distance IMMO...

Reset Steering angle sensor via X431 PRO for Buick New Lacrosse

02/20/2021 18:14
This instruction show you guide on how to reset steering angle sensor by X431 PRO. If you want to know more about X431, please click here: How to use launch X431. Steps: Connect X431 interface to Buick New Lacrosse obd port, then run X431 soft. After enter into ESP system,Read 6 error code: U0073...

How to Use Volvo PTT to Diagnose Volvo FM440 Truck

02/11/2021 18:36
This instruction show you guide on how to use Volvo PTT to diagnose engine performance for Volvo FM440 truck. Preparations: How to Download,Install and Activate Volvo Premium Tech Tool PTT 2.7.98? Diagnose Volvo FM440 Truck Engine Performance by Volvo PTT: Connect Volvo PTT interface (VOCOM...

Autel MaxiIM508 + XP400 add keys for 2011 BMW M3 CAS3 step by step

02/11/2021 18:34
Adding a 2011 BMW M3 CAS3+ key via Autel MaxiIM508 W/XP400. had to updated the cas3 module first then do procedure to add a new blank OEM Key. Key has OEM internals with aftermarket case.\ Question: Have Autel MaxiIM608 (=Autel MaxiIM508 + XP400) and doing a CAS3 on the bench today to add key, I...

W124 W212 Xentry star diagnostics Recommend

02/04/2021 13:33
Have a Mercedes W124 2.5d from 1992, W124 2.0 petrol from 1994 and a W212 E350 CDI 10 plate to diagnose, not sure which Xentry Kits to buy, SD Connect C4 is the best. Car model: A Mercedes W124 2.5d from 1992, W124 2.0 petrol from 1994 and a W212 E350 cdi 10 plate. Purpose: I would like to...

ICOM (genuine) Firmware Update Files

02/04/2021 13:23
Hello, guys. I have ICOM Next A (genuine, gray and black) Part Number 81-31-2-360-883. I bought it 2 years ago, so I need a firmware update files for 2020 ISTA+. Bin firmware files that I have with my 2020 ISTA+ HDD  give me a warning “Warning: the image file doesn’t match to the ICOM type” I...

CDA Working With VCI Pod Or Micropod 2

01/06/2021 19:58
What is CDA?  CDA (Chrysler Diagnostic Application) is a powerful dealer tool that allows to make option changes in the VIN. Say for example you have a Chrysler 300, and you go like, gee I would sure like some steering wheel controls, or some dual climate, or some other option! Then you logon...
<< 2 | 3 | 4 | 5 | 6 >>

Honda Key Programmer

07/01/2018 16:10

Honda Key Programmer Cover all Honda/Acura equipped with OBDII-16 socket from 1999 to 2018

17-1

Highlights:
a) Easy to use. Register keys full automatically. User just turns ignition ON/OFF.
b) Register keys fast. Finish registration in minutes.
c) Small package and easy to carry. Can be hold in one hand.

The device is for registering key by OBDII. Cover all Honda/Acura equipped with OBDII-16 socket from 1999 to 2018. Support both transponder key and smart key registration in the following scenarios:

Functions:
a) Add key
b) All keys lost
c) Replace IMMOBI
d) Replace ECM/PCM
e) Replace MPCS/MICU/IMOES
f) Replace smart entry
g) Replace key knob
h) Remote learning

Operation Instructions:
For transponder key.
1.Switch to “IMMO”, and prepare all keys to register.
2.Turn ignition ON to position II(Instrument panel light on but engine OFF), connect programmer to OBDII socket
3.The buzzer periodically short beep with “Di”, Turn ignition OFF.
4.The buzzer periodically short beep with “Di, Di, Di”, turn ignition on without changing key.
5.The buzzer long beep once “Di—“, key registration begins.
6.The buzzer periodically short beep with “Di”, Turn ignition OFF.
7.The buzzer periodically short beep with “Di, Di”, Change another key and turn ignition ON
8.Repeat step F,G, register more up to 6 keys.
9.For last key: First turn ignition ON/OFF following above instructions. When the buzzer periodically short beep with “Di Di”, turn on ignition WITHOUT changing key. Then the buzzer periodically short beep with “Di”, DO NOT turn off ignition and keep ignition on for more than 20 seconds.
10.The buzzer long beep once “Di—“, key registration finished.
11.The buzzer periodically long beep with “Di—“, start to learn remote function. Learning remote function instruction: close all doors, press and release lock/unlock button on key in 4 seconds until door locks lock/unlock. Then learn next remote.(Some cars do not need remote learning, and no buzzer beep tips for learning remote)
12.Turn ignition OFF. Pull out programmer from OBDII. Try to start engine with every key.

For smart key
1.Switch to “SMRT”, and prepare all smart cards to register. Only 1 card in car, and the others out of car.
2.Push one-push-start button, or use ignition key in card, turn ignition ON(Instrument panel light on but engine OFF). If all cards lost and can’t turn ignition on, press and hold one-push-start button. Connect programmer to OBDII socket.
3.The buzzer periodically short beep with “Di”, turn ignition OFF
4.The buzzer periodically short beep with “Di, Di, Di “, turn ignition ON.
5.The buzzer long beep once “Di—“, card registration begins.
6.The buzzer periodically short beep with “Di”, take card out of car.
7.The buzzer periodically short beep with “Di, Di”, take another card in car.
8.Repeat step F,G, register more up to 6 cards
9.For last card: First take card in car following instruction. When the buzzer periodically short beep with “Di”, DO NOT take card out of car and keep card in car for more than 100 seconds.
10.The buzzer long beep once “Di—“, cards registration finished.
11.Turn ignition OFF. Pull out programmer. Try to start engine with every card.

Key Programming Technical Specifications:
a) Voltage & Current Requirements 8V – 18V DC (12V nominal) at 4 Amps (maximum)
b) Vehicle Protocols
– DIAGH
– CAN
– ISO-9141
– ISO-14230
c) Vehicle Connection Molded DLC
d) Dimensions H:22mm (0.87in) W:54mm (2.13in) L:76mm (2.99in)
e) Weight 50g (1.76oz)
f) Environmental Operating: -20oC to 45oC (-4oF to 113oF) at 15% to 85% RH non-condensing

Appearance Detail :

17-2 17-3

a) Key Type Switch
IMMO: Transponder key
SMRT: Smart key
b) LED Status Indicators
ON: Power ON
OFF: Power OFF
c) Buzzer
– Long beep once “Di—” (Beep ON continuous for 3 seconds)
– Long beep periodically with “Di—“(Beep ON for 1 second and OFF for 1 second, and repeat)
– Short beep periodically with “Di” (Beep ON for 100 milliseconds, OFF for 900 milliseconds, and repeat)
– Short beep periodically with “Di, Di” (Beep ON for 100 milliseconds, OFF for 100 milliseconds, ON for 100 milliseconds, OFF for 700 milliseconds, and repeat)
– Short beep periodically with ” Di, Di, Di” (Beep ON for 100 milliseconds, OFF for 100 milliseconds, ON for 100 milliseconds, OFF for 100 milliseconds, ON for 100 milliseconds, OFF for 500 milliseconds, and repeat)