Search site

Contact

Car diagnostic tools information by obd2tool

https://www.obd2tool.com

Welcome to my blog,here some auto diagnostic tools will be displayed. If you want to know more information,you can visit our official website: www.obd2tool.com.

lovelily750@gmail.com

News

Visitors notice

12/01/2014 07:47
Let your visitors know about news and events on your website as often as possible. You need to keep your website up-to-date so that your visitors will get used to visiting your pages regularly. You can use RSS feeds to deliver new articles directly to your readers.

Website launched

12/01/2014 07:46
Our new website has been launched today. Tell your visitors why you have started a new presentation and how it benefits them. Mention your goals and project advantages. Try to briefly give your visitors reasons why they should return to your pages.

The blog of OBD2 TOOL

How to update BMW ICOM A2 or ICOM NEXT Firmware

05/27/2021 09:41
When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware...

Active Hidden Function via X431 PRO for Toyota Reiz 2015

05/13/2021 16:34
Here we will show you how to active hidden function by X431 PRO for Toyota Reiz 2015. Function has been already tested on Toyota below: Automatic padlock Switch off the ignition about 30S/60S/120S Automatic padlock setting; 3 Press Remote control one time or twice to unlock setting.; 4....

Benz W211 Gearbox Programming & Coding by Launch X431

04/09/2021 17:15
After replacing gearbox valve body or gearbox ECU, it is required to perform programming and coding. If still unable to engage the gear or the gear is locked at 3rd gear position, Gearbox Self-learning shall be performed.When strong shock is felt during gearshift, perform this function.So here...

How to Configure WiFi and USB for Original JLR DoIP VCI

03/28/2021 17:08
Part 1: How to Configure WiFi for Original JLR DoIP VCI /setup wireless connection? Original Jaguar Land Rover diagnostic tool JLR DoiP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting. Procedure: Connect JLR DoiP VCI W-F interface with...

How to Restore X431 V X-431 Pro to Factory Settings

03/12/2021 17:34
How to Restore X431 V X-431 Pro to Factory Settings ? Read this before operation: 1. The following method does not apply to X431 V+ and X431 Pro3 2. Please use this function carefully, improper operation may cause the dead of X431 V, besides, after the factory settings are restored, all user...

How to Use HP Tuners vs. Y2K Silverado LM7 & TSP Peformance Cam

03/05/2021 10:08
To begin this HP Tuners Thread… The FIRST Place I went directly to was THIS Site: HPTuners – Connect > Read > Edit > Write > Drive HP Tuners, the home of VCM Suite and the MPVI since 2003. Now enhancing these to new heights with a new feature rich VCM Editor and VCM Scanner, coupled...

How to Use Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007

02/20/2021 18:27
I am gonna use the new tool Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007. The scanner just came to me last week. Xhorse VVDI Key Tool Plus supports DOIP/CAN-FD/ CAN and K protocol switch pin/Chip pin detection/Toyota smart key programming without simulator/Long distance IMMO...

Reset Steering angle sensor via X431 PRO for Buick New Lacrosse

02/20/2021 18:14
This instruction show you guide on how to reset steering angle sensor by X431 PRO. If you want to know more about X431, please click here: How to use launch X431. Steps: Connect X431 interface to Buick New Lacrosse obd port, then run X431 soft. After enter into ESP system,Read 6 error code: U0073...

How to Use Volvo PTT to Diagnose Volvo FM440 Truck

02/11/2021 18:36
This instruction show you guide on how to use Volvo PTT to diagnose engine performance for Volvo FM440 truck. Preparations: How to Download,Install and Activate Volvo Premium Tech Tool PTT 2.7.98? Diagnose Volvo FM440 Truck Engine Performance by Volvo PTT: Connect Volvo PTT interface (VOCOM...

Autel MaxiIM508 + XP400 add keys for 2011 BMW M3 CAS3 step by step

02/11/2021 18:34
Adding a 2011 BMW M3 CAS3+ key via Autel MaxiIM508 W/XP400. had to updated the cas3 module first then do procedure to add a new blank OEM Key. Key has OEM internals with aftermarket case.\ Question: Have Autel MaxiIM608 (=Autel MaxiIM508 + XP400) and doing a CAS3 on the bench today to add key, I...
<< 1 | 2 | 3 | 4 | 5 >>

How to convert HALOGEN to LCI HEADLIGHT with a ICOM cable

09/20/2018 21:46

It’s a HALOGEN TO LCI HEADLIGHT Tutorial!!!!

Excuse my English I hope this help some of you guys!

In this site you will see the diagram for wiring!

Now after you know what your going to do with the wiring uninstall the frm and install frm2.

You will need NCS expert and Winkfp and inpa! and the icom cable obd to the computer! when you get the cable just read instruction and you ill be fine.. but just in case if your cable didnt bring the instruction here is how to program the cable make sure the computer read the cable if not download the driver after your pc read cable go to start on computer right click properties, device manager,then PORT click on it look for the cable then double click then a window will open lick on port setting (tap) click on advance at the bottom and make sure to set COM to COM1 and the latency to 1 it should be on 16 from default click ok and you are ready to go!

After you install all this software you need to open NCS expert to Change VO and VIN to yor frm2. And then program it!

OK now if you have AHL you need to add this VOs $522 and $524 to CAS and FRM and change production date that is going to be like this for example (#1205) you have to change it to at least #0307. and if you have just xenon add $522 and production date #0307. NOW question is how to do it.

open NCS expert on file tap load profile select expert mode F1,F3 select chassis e89 and select CAS now F2 (ENTER FA) select chassis again then enter vin# of the car

now a new window will open with a list of numbers.. is gonna say attribute ADD and OK at the bottom now we are going to add $522 and $524 and click in top of the first one that is the production date and hit the delete bottom on your keyboard and add the #0307 and click OK then F6 back then choose F4 choose CAS then F2 change job to FA_WRITE and F3 execute job and you are done!

Now you have to pass that information to “NFRM”

1.open NCS expert

2.File-Load profile

3.select EXPERMODE

4.press F1

5.press F3

6.select E89<for E90>

7.select CAS

8.F6 back

9.now you will be able to see your (FG) VIN # at top and (FA) VO

10.press F4<CHOOSE ECU>

11.select NFRM

12.after that select F2 chenge Job

13 choose FA_WRITE

14.F3 executive job wait a little bit and it will say courin beenet or coded ended something like that! now your VO are the same CAS and NFRM

NOW to change VIN

I did it the same way as CAS but instead of choose FA_WRITE i Choose FG_SCHREIBEN

1.open NCS expert

2.File-Load profile

3.select EXPERMODE

4.press F1

5.press F3

6.select E89<for E90>

7.select CAS

8.F6 back

9.now you will be able to see your (FG) VIN # at top and (FA) VO

10.press F4<CHOOSE ECU>

11.select NFRM

12.after that select F2 chenge Job FG_SCHREIBEN then F3 execute Job

now to make sure everything is good Go back to the main menu (or restart ncs-expert) and get the vehicle order from the “NFRM” module. Make sure NFRM returns YOUR VIN and YOUR VO. We want the VIN (FG) and VO (FA) to be the same in both CAS and NFRM. To do this same steps load profile expertmode F1,F3 select chassis and select “NFRM” NOT CAS!!! and it should be your VIN and VO the same as CAS.

Now to program NFRM you have to use Winkfp but first you need to know the part number of the NFRM using inpa that is gonna show on inpa FRM_70. go to inpa folder and look for inpaload select chassis and a window will open and select the first one functional jobs then f2 indet in there you will look for FRM_70 and copy the ZUB that is the part number IT should say for example (9204527) this is a example copy that number down and close inpa. now open Winkfp and choose confort mode F1 enter ZUSB put the number that you wrote down here and ill look for your frm automatically click ok then F4 Enter Vin put your car vin # click ok and then update ZUSB look for the one that gives you in the first step for ex(FRM2) then click on done! if it gives you an error 106 is because you dont have the cable plug in into the car! after that lick on F3 Prog. ZB UPdate and wait until is done and you are done!

Now to make sure BMW Diagnostic Software NFRM is default in NCS expert

load profile then go back to file and click edit file and click on FSW/PSW and uncheck the option “FSW/PSW manipulate with FSW_PSW.MAN” then click ok and choose profile info and on the name put whatever name that will remember you that thats the profile to code to factory any ecu using NCS expert then click ok and ok again that windows will close and click file save as and put the name that you choose.. Then F1, F3 choose chassis then CAS then F4 choose NFRM then F2 SG_codieren then F3 done!

Now to code with NCS expert you will need to create a FSW_PSW TRC file..

here is a video on Youtube but just in case if the video is not working ill write it down

To do this you have to Open NCS expert load profile expertmode

same F1,F3 select chassis select CAS F6 back choose ecu F4 NFRM and change job F2 CODIERDATEN_LESEN then f3 execute job now dont close ncs expert and go to ncs expert folder then to work folder and you will see that there is a FSW_PSW trc file open the file change what ever you need to change and after you change everything save the file.. go to file and click save as and write FSW_PSW.MAN now go back to NCS expert and Click on file edit file and go to FSW_PSW click on it and make sure to check the option FSW_PSW manipulate with FSW_PSW.MAN click ok then choose ECU F4 select the Ecu that you choose to read with CODIERDATEN_LESEN earlier and now change to to SG_codieren and F3 execute job and You are DONE coding!

THANK YOU FOR READING I HOPE THIS WILL HELP SOMEONE I SPENT 2 WEEK TO LEARN ALL THIS AND NOW I WANT TO SHOW IT TO YOU GUYS!