Search site

Contact

Car diagnostic tools information by obd2tool

https://www.obd2tool.com

Welcome to my blog,here some auto diagnostic tools will be displayed. If you want to know more information,you can visit our official website: www.obd2tool.com.

lovelily750@gmail.com

News

Visitors notice

12/01/2014 07:47
Let your visitors know about news and events on your website as often as possible. You need to keep your website up-to-date so that your visitors will get used to visiting your pages regularly. You can use RSS feeds to deliver new articles directly to your readers.

Website launched

12/01/2014 07:46
Our new website has been launched today. Tell your visitors why you have started a new presentation and how it benefits them. Mention your goals and project advantages. Try to briefly give your visitors reasons why they should return to your pages.

The blog of OBD2 TOOL

Ford VCM II firmware update or downgrade

06/25/2021 11:33
It’s confirmed that Ford VCM II Firmware Update And Downgrade is possible, Operation steps guide here (This guide applies to all vcmii tools) Procedure: Remove the rubber case shown below. Connect the USB cable to the VCM2 device and hold the (ReSet) button shown as below. Connect the other...

Top 5 Launch X431 Diagnostic Tool Review 2021

05/27/2021 09:45
Launch X431 Diagnostic Tool is one of best and professional car diagnostic tools in the automotive aftermarket. Launch X431 is aim to provide the most innovative and cost-effective solutions for auto diagnosis work. Launch X431 series diagnostic tool have full line device to meet different...

How to update BMW ICOM A2 or ICOM NEXT Firmware

05/27/2021 09:41
When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware...

Active Hidden Function via X431 PRO for Toyota Reiz 2015

05/13/2021 16:34
Here we will show you how to active hidden function by X431 PRO for Toyota Reiz 2015. Function has been already tested on Toyota below: Automatic padlock Switch off the ignition about 30S/60S/120S Automatic padlock setting; 3 Press Remote control one time or twice to unlock setting.; 4....

Benz W211 Gearbox Programming & Coding by Launch X431

04/09/2021 17:15
After replacing gearbox valve body or gearbox ECU, it is required to perform programming and coding. If still unable to engage the gear or the gear is locked at 3rd gear position, Gearbox Self-learning shall be performed.When strong shock is felt during gearshift, perform this function.So here...

How to Configure WiFi and USB for Original JLR DoIP VCI

03/28/2021 17:08
Part 1: How to Configure WiFi for Original JLR DoIP VCI /setup wireless connection? Original Jaguar Land Rover diagnostic tool JLR DoiP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting. Procedure: Connect JLR DoiP VCI W-F interface with...

How to Restore X431 V X-431 Pro to Factory Settings

03/12/2021 17:34
How to Restore X431 V X-431 Pro to Factory Settings ? Read this before operation: 1. The following method does not apply to X431 V+ and X431 Pro3 2. Please use this function carefully, improper operation may cause the dead of X431 V, besides, after the factory settings are restored, all user...

How to Use HP Tuners vs. Y2K Silverado LM7 & TSP Peformance Cam

03/05/2021 10:08
To begin this HP Tuners Thread… The FIRST Place I went directly to was THIS Site: HPTuners – Connect > Read > Edit > Write > Drive HP Tuners, the home of VCM Suite and the MPVI since 2003. Now enhancing these to new heights with a new feature rich VCM Editor and VCM Scanner, coupled...

How to Use Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007

02/20/2021 18:27
I am gonna use the new tool Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007. The scanner just came to me last week. Xhorse VVDI Key Tool Plus supports DOIP/CAN-FD/ CAN and K protocol switch pin/Chip pin detection/Toyota smart key programming without simulator/Long distance IMMO...

Reset Steering angle sensor via X431 PRO for Buick New Lacrosse

02/20/2021 18:14
This instruction show you guide on how to reset steering angle sensor by X431 PRO. If you want to know more about X431, please click here: How to use launch X431. Steps: Connect X431 interface to Buick New Lacrosse obd port, then run X431 soft. After enter into ESP system,Read 6 error code: U0073...
1 | 2 | 3 | 4 | 5 >>

How to Program BMW F30 FEM Key with CGDI Prog Key Programmer

10/28/2017 23:11

Here’s the little guide on programming key on a BMW F30 FEM system with CGDI Prog BMW MSV80 Car Key Programmer.

Device required:

CGDI Prog BMW key programmer

BMW FEM/BDC Test Platform for BMW  F20 F30 F35 X5 X6 I3

Preparation:

Disassemble the FEM/BDC module from vehicle

Procedure:

Connect BMW FEM/BDC test platform with CGDI Prog and FEM/BDC module from Obd2tool.com

cgdi-prog-1

cgdi-prog-2
cgdi-prog-3

Open CGDI Prog BMW software

cgdi-prog-4
Select FEM/BDC Key Match

cgdi-prog-5

The current FEM BDC needs to update the ECU program before performing key matching. Please ensure that the car battery has enough power supply. Please do not disconnect cable connection during programming procedure.

cgdi-prog-6

Please remove the FEM BDC and then use the programmer to read and save the data from the
95xxx EEPROM chip on the FEM/BDC computer board, then click “Next”
cgdi-prog-7
Please read the original car EEPROM data

cgdi-prog-8

cgdi-prog-9
cgdi-prog-10

cgdi-prog-11

Read eeprom data with Key Programm Tool, i.e Orange 5 eeprom programmer

and save data

cgdi-prog-12

cgdi-prog-13

User the programmer to write the calculated new data to the 95xxx eeprom chip, then put the FEM BDC back to the car
click Next

cgdi-prog-14
Click OK to write M95128

User the programmer to write the calcutaed new data to the 95xxx eeprom chip, then put the FEM BDC back to the car
click Next

Power on BMW FEM BDC test platform

The yellow indicator will flash

cgdi-prog-15
cgdi-prog-16

Coding is being backed up

The ECU is being programmed

and verify flashing

cgdi-prog-17

cgdi-prog-18

Program BMW F30 FEM key success

cgdi-prog-19

 

https://cheapobd2scanner.com/2017/10/23/how-to-program-bmw-f30-fem-key-with-cgdi-prog-key-programmer/