Search site

Contact

Car diagnostic tools information by obd2tool

https://www.obd2tool.com

Welcome to my blog,here some auto diagnostic tools will be displayed. If you want to know more information,you can visit our official website: www.obd2tool.com.

lovelily750@gmail.com

News

Visitors notice

12/01/2014 07:47
Let your visitors know about news and events on your website as often as possible. You need to keep your website up-to-date so that your visitors will get used to visiting your pages regularly. You can use RSS feeds to deliver new articles directly to your readers.

Website launched

12/01/2014 07:46
Our new website has been launched today. Tell your visitors why you have started a new presentation and how it benefits them. Mention your goals and project advantages. Try to briefly give your visitors reasons why they should return to your pages.

The blog of OBD2 TOOL

How SKP-900 key programmer add Ford Focus remote key in 3 steps

01/28/2018 15:42
This blog will manage customers to add Ford focus remote keys with SuperOBD SKP900 Hand-held Auto Key Programmer, just need 3 steps, spend you several minutes. Vehicle: Ford Focus Tool Used: SKP-900 auto key programmer Detail steps: Step1 Connect key programmer SKP-900 to the car. Enter...

SKP900 Key Programmer Land Rover All Key Lost Car List

01/17/2018 19:58
SuperOBD SKP-900 key programmer is advised for both experienced locksmith and car owners. It supports program Land Rover key when all key lost, many other brands as well. This blog will show you which models all key lost SKP900 support and how to do. SKP900 Land Rover All Key Lost Car...

VCM II For Ford IDS 106.01 MAZDA 106.00 Software Free Share & Guide

01/07/2018 15:58
VCM II VCM 2 For Ford IDS 106.01 MAZDA 106.00 VMWare NEW Updated.And this blog will share Ford IDS 106.01 MAZDA 106.00 free Software download as well as some FAQs users maybe will  meet when installing or using new software ,so let’s start it now. New VCM II IDS Software Free Download...

(Tested) Autel DS708 read pin code program key for Vauxhall Meriva

12/23/2017 21:29
This blog will share a success case: using Autel MaxiDAS DS708 to read pin code then program remote key for Vauxhall Meriva 1.7 CDTi 2004! Below is procedure for your reference. How use MaxiDas DS708 read pin code program key for Vauxhall Meriva? First connect autel scan tool DS708...

CGDI Prog BMW and Mercedes Key Programmer Test Report

12/12/2017 13:52
CGDI Prog MB Mercedes and CGDI Prog BMW are two different tools from the Obd2tool.com whom manufactured CG100 airbag reset tool.   How they works? See the test reports with photos. CGDI Prog BMW CGDI Prog MB Mercedes 1.CGDI Prog BMW program X6 BDC key via OBD CGDI BMW program 5...

Lonsdor K518 Program Ford Edge pre-2015 Smart Key by OBD

12/05/2017 10:14
Here’s guide to program smart keys to Ford Edge pre-2015 by using Lonsdor K518ISE Key Programmer via OBD without pin code. Key information: Original key: 5-button smart key Frequency: 433MHz Pin code: No Key required: at least 2 smart keys Card slot: central console box Device to...

The top 5 reason to get CRP129 Premium

11/28/2017 17:24
The Launch CRP123 & CRP129 code readers have been market leaders for many years and now have been upgraded to a “Premium” edition. The new Premium series boasts a larger 4” color display, increased storage, revised button layout for improved navigation and a direct USB connection for ease...

How to read VW Pin code with Lonsdor K518, Xtool X100 Pad2 and VVDI2

11/26/2017 11:16
There are several tools available to read pin code and program key for VAG group. Here are the demo guides to read pin code for VAG.   1) Read VAG Pin Code with Lonsdor K518 Lonsdor K518ISE Key Programmer comes with built-in Volkswagen 4th & 5th adapter, so it can read pin code...

All Autel Product Software update Instructions

11/20/2017 15:21
Software update Instructions Suitable for Autel MaxiSys Pro MS908P ,  Autel DS708, Autel TS501,Autel TS601,, AL609, AL619, VAG505, MOT PRO, MaxiDiag Elite, MaxiCheck….. Autel Tools FAQ 1.Update Software and serial number: 1). Update and Registration: all Autel scanners with SD card need...

How to Program BMW F30 FEM Key with CGDI Prog Key Programmer

10/28/2017 23:11
Here’s the little guide on programming key on a BMW F30 FEM system with CGDI Prog BMW MSV80 Car Key Programmer. Device required: CGDI Prog BMW key programmer BMW FEM/BDC Test Platform for BMW  F20 F30 F35 X5 X6 I3 Preparation: Disassemble the FEM/BDC module from...
<< 3 | 4 | 5 | 6 | 7 >>

GM SPS Programming: Tech2 Tool Remote Mode ECU TIS2000 Calibration Update

01/01/2019 21:41

Here is the step-by-step instruction on programming GM (General Motors) ECUs with Tech 2 Scanner and SPS (Service Programming System) application in TIS2000.

NOTE:

Before using the SPS, make sure that the Tech 2 scan tool and the pc contain the latest software, the battery of the vehicle is fully charged, only the ignition is on power, and all cables are connected properly. TIS2000 will not work on 2007 up GM, and software must work together with TIS2000 USB key. If you need to program Saab ECU, you had to use Saab TIS2000 and USB dongle.

Main steps:

Step 1: Instruction for TIS2000 software

Step 2: Data request

Step 3: Data exchange

Step 4: Program ECU

Alternative Programming with “Pass Thru”

Check Programming result

Step 1: Instruction for TIS2000 software

1.Connect the Tech II to the pc.

Note: The hardware key (HWK) has to be registered prior to working with ‘Service Programming System’. To register a hardware key, the form that is enclosed with the hardware key kit has to be filled in and sent to the address at the top. In case the form is missing, the document is also in the TIS 2000 newsletter (see icon in the TIS 2000 tool bar). At first, the user receives a temporary code until the key is registered on the next TIS 2000 CD.

Hardware keys that have already been registered are still valid!

To register the hardware key select ‘Hardware Key Registration’ in the menu ‘Configuration’.

TIS2000 installation video guide
*   Start TIS 2000 on the pc.
*   Select the application ‘Service Programming System’ on the TIS 2000 start page.

Tech2-program-ecu-with-sps-in-tis2000-1

4. On ‘Select Diagnostic Tool and Programming Process’ (picture below) screen make the desired selection for

1) the used Tech2 diagnostic tool

2) the reprogramming of an ECU that was not exchanged or the replacement/programming of a new ECU

3) the ECU location.

Tech2-program-ecu-with-sps-in-tis2000-2

*   Click “Next” button to continue.

Step 2: Data Request

*   Connect Tech 2 scanner to vehicle. Power on device – “Tech 2” is displayed on the screen, then press “ENTER”.

*   Turn ignition to ON without start the engine!!!

*   Select “F1: Service Programming System (SPS)” in the main menu.

*   Press “F0: Request Info” on Tech 2.

*   If Tech 2 has already stored vehicle data they will be displayed now. In that case, Tech 2 asks you to either use the current data (hold data) or request further information from the ECU (continue).

*   For the selection of “Next” the vehicle has to be identified as requested by Tech 2.

Note: Depending on the model year and the selected model either a reprogramming of the ECU (F0: Engine) or of the TCM (F1: Transmission) can be selected.

*   During the Request Info the Professional Diagnostic Tool information from the selected device. If the ECU was replaced a “Request Info” has to be performed for the NEW unit. Since the new ECU is not programmed on delivery, the retrieved information is not complete. For that reason, TIS 2000 gives instructions as how to enter the missing vehicle data.

*   Follow the instructions on the Tech 2 on OBD2TOOL. Then press “Exit” on the Tech 2, switch it off and disconnect it from the vehicle.

Step 3: Data exchange

*   Connect Tech 2 to the pc, switch it on, and click on ‘Next’ on the pc.
*   Confirm VIN or, if necessary, enter correct VIN, then select ‘Next’.

Tech2-program-ecu-with-sps-in-tis2000-3

*   Validate vehicle data and, if necessary, change with the pull-down menus.
*   Click on ‘Next’. Button

Tech2-program-ecu-with-sps-in-tis2000-4

*   A new window displays a “Summary” (follow below) with the selected data. Continue with ‘Next’. Select “Reprog” button to download the latest calibration data onto the TechII diagnostic tool.

Note: It is not possible to reprogram an ECU with the same software version.

Tech2-program-ecu-with-sps-in-tis2000-5

*   The window ‘Transfer Data’ is displayed. A bar shows the progress of the download.

At the end of the download, a window is displayed with the request to connect the Tech 2 to the vehicle in order to finish the programming process.

Tech2-program-ecu-with-sps-in-tis2000-6

*   After the closing of the SPS application the TIS 2000 start screen is again displayed. Finally, switch off the Tech 2 and disconnect it from the pc.

Step 4: Program ECU

*   Connect Tech 2 to the vehicle.
*   Switch on Tech 2 – start screen appears.
*   Turn ignition (Do not start motor!).
*   Press “Enter” in the Tech 2 start screen.
*   Select “F1: Service Programming System” in the main menu and then “F1: Program ECU”.
*   Follow the instructions on the Tech 2 screen.
*   During the download the Tech 2 screen shows the message “Programming in Progress”.
*   At the end of the download the Tech 2 shows the message “Programming was successful”. The button “Exit” leaves the program. First, turn off the ignition of the vehicle, then switch off the Tech 2 and disconnect it from the vehicle.
*   Turn off ignition for 30 seconds before starting the motor. Additional information is available in the section “Check programming”.

Alternative Programming with “Pass Thru”

In addition to the procedure described above, there is an alternative programming mode called “Pass Thru”. In that case, the data are directly downloaded from the pc to the ECU in the vehicle.

Although the Tech 2 is still needed in that mode, the data entry and the download control is done directly at the pc. Altogether, that method is faster, and it is recommended when a pc with TIS 2000 is within 3m of the vehicle.

*   Connect Tech 2 to the vehicle.
*   Connect Tech 2 to the PC switch on Tech 2.
*   Start TIS 2000 on the PC.
*   Select the icon ‘Service Programming System’ (Fig. 1) on the TIS 2000 start page.
*   Start TIS 2000 on the PC.
*   On the screen ‘Select Diagnostic Tool and Programming Process’ (See picture below) make a selection for

***Pass-Thru mode

***the reprogramming of an ECU that was not exchanged or the replacement/programming of a new ECU

***the ECU location.

Then clock ‘Next’ button.

Tech2-program-ecu-with-sps-in-tis2000-7

Check programming result

After every repgrogramming of an ECU a test to check the successful programming has to perform as follows:

*   turn off ignition
*   wait for at least 30 seconds
*   start motor to confirm the successful programming
*   If the motor doesn’t start this points at an error. After the replacement of an ECU it has to be made sure that the necessary programming of the immobilizer was successful.