Search site

Contact

Car diagnostic tools information by obd2tool

https://www.obd2tool.com

Welcome to my blog,here some auto diagnostic tools will be displayed. If you want to know more information,you can visit our official website: www.obd2tool.com.

lovelily750@gmail.com

News

Visitors notice

12/01/2014 07:47
Let your visitors know about news and events on your website as often as possible. You need to keep your website up-to-date so that your visitors will get used to visiting your pages regularly. You can use RSS feeds to deliver new articles directly to your readers.

Website launched

12/01/2014 07:46
Our new website has been launched today. Tell your visitors why you have started a new presentation and how it benefits them. Mention your goals and project advantages. Try to briefly give your visitors reasons why they should return to your pages.

The blog of OBD2 TOOL

How to Reset OBDSTAR X300 DP Plus to Solve Register Failure Problem

07/31/2021 15:49
Here share the method to solve OBDSTAR X300 DP PLUS register failure problem by resetting the device. Customer problem: When I turned on my x300 dp plus, and tapped teamviewer to register, the registration interface appeared, but quickly jumped back to the user login interface. I tried it many...

How to update the firmware of ICOM NEXT A

07/31/2021 15:25
Upgraded the new version of BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next; ICOM NEXT A firmware upgrade steps 1. First, you need the firmware...

Ford VCM II firmware update or downgrade

06/25/2021 11:33
It’s confirmed that Ford VCM II Firmware Update And Downgrade is possible, Operation steps guide here (This guide applies to all vcmii tools) Procedure: Remove the rubber case shown below. Connect the USB cable to the VCM2 device and hold the (ReSet) button shown as below. Connect the other...

Top 5 Launch X431 Diagnostic Tool Review 2021

05/27/2021 09:45
Launch X431 Diagnostic Tool is one of best and professional car diagnostic tools in the automotive aftermarket. Launch X431 is aim to provide the most innovative and cost-effective solutions for auto diagnosis work. Launch X431 series diagnostic tool have full line device to meet different...

How to update BMW ICOM A2 or ICOM NEXT Firmware

05/27/2021 09:41
When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware...

Active Hidden Function via X431 PRO for Toyota Reiz 2015

05/13/2021 16:34
Here we will show you how to active hidden function by X431 PRO for Toyota Reiz 2015. Function has been already tested on Toyota below: Automatic padlock Switch off the ignition about 30S/60S/120S Automatic padlock setting; 3 Press Remote control one time or twice to unlock setting.; 4....

Benz W211 Gearbox Programming & Coding by Launch X431

04/09/2021 17:15
After replacing gearbox valve body or gearbox ECU, it is required to perform programming and coding. If still unable to engage the gear or the gear is locked at 3rd gear position, Gearbox Self-learning shall be performed.When strong shock is felt during gearshift, perform this function.So here...

How to Configure WiFi and USB for Original JLR DoIP VCI

03/28/2021 17:08
Part 1: How to Configure WiFi for Original JLR DoIP VCI /setup wireless connection? Original Jaguar Land Rover diagnostic tool JLR DoiP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting. Procedure: Connect JLR DoiP VCI W-F interface with...

How to Restore X431 V X-431 Pro to Factory Settings

03/12/2021 17:34
How to Restore X431 V X-431 Pro to Factory Settings ? Read this before operation: 1. The following method does not apply to X431 V+ and X431 Pro3 2. Please use this function carefully, improper operation may cause the dead of X431 V, besides, after the factory settings are restored, all user...

How to Use HP Tuners vs. Y2K Silverado LM7 & TSP Peformance Cam

03/05/2021 10:08
To begin this HP Tuners Thread… The FIRST Place I went directly to was THIS Site: HPTuners – Connect > Read > Edit > Write > Drive HP Tuners, the home of VCM Suite and the MPVI since 2003. Now enhancing these to new heights with a new feature rich VCM Editor and VCM Scanner, coupled...
1 | 2 | 3 | 4 | 5 >>

GM SPS Programming: Tech2 Tool Remote Mode ECU TIS2000 Calibration Update

01/01/2019 21:41

Here is the step-by-step instruction on programming GM (General Motors) ECUs with Tech 2 Scanner and SPS (Service Programming System) application in TIS2000.

NOTE:

Before using the SPS, make sure that the Tech 2 scan tool and the pc contain the latest software, the battery of the vehicle is fully charged, only the ignition is on power, and all cables are connected properly. TIS2000 will not work on 2007 up GM, and software must work together with TIS2000 USB key. If you need to program Saab ECU, you had to use Saab TIS2000 and USB dongle.

Main steps:

Step 1: Instruction for TIS2000 software

Step 2: Data request

Step 3: Data exchange

Step 4: Program ECU

Alternative Programming with “Pass Thru”

Check Programming result

Step 1: Instruction for TIS2000 software

1.Connect the Tech II to the pc.

Note: The hardware key (HWK) has to be registered prior to working with ‘Service Programming System’. To register a hardware key, the form that is enclosed with the hardware key kit has to be filled in and sent to the address at the top. In case the form is missing, the document is also in the TIS 2000 newsletter (see icon in the TIS 2000 tool bar). At first, the user receives a temporary code until the key is registered on the next TIS 2000 CD.

Hardware keys that have already been registered are still valid!

To register the hardware key select ‘Hardware Key Registration’ in the menu ‘Configuration’.

TIS2000 installation video guide
*   Start TIS 2000 on the pc.
*   Select the application ‘Service Programming System’ on the TIS 2000 start page.

Tech2-program-ecu-with-sps-in-tis2000-1

4. On ‘Select Diagnostic Tool and Programming Process’ (picture below) screen make the desired selection for

1) the used Tech2 diagnostic tool

2) the reprogramming of an ECU that was not exchanged or the replacement/programming of a new ECU

3) the ECU location.

Tech2-program-ecu-with-sps-in-tis2000-2

*   Click “Next” button to continue.

Step 2: Data Request

*   Connect Tech 2 scanner to vehicle. Power on device – “Tech 2” is displayed on the screen, then press “ENTER”.

*   Turn ignition to ON without start the engine!!!

*   Select “F1: Service Programming System (SPS)” in the main menu.

*   Press “F0: Request Info” on Tech 2.

*   If Tech 2 has already stored vehicle data they will be displayed now. In that case, Tech 2 asks you to either use the current data (hold data) or request further information from the ECU (continue).

*   For the selection of “Next” the vehicle has to be identified as requested by Tech 2.

Note: Depending on the model year and the selected model either a reprogramming of the ECU (F0: Engine) or of the TCM (F1: Transmission) can be selected.

*   During the Request Info the Professional Diagnostic Tool information from the selected device. If the ECU was replaced a “Request Info” has to be performed for the NEW unit. Since the new ECU is not programmed on delivery, the retrieved information is not complete. For that reason, TIS 2000 gives instructions as how to enter the missing vehicle data.

*   Follow the instructions on the Tech 2 on OBD2TOOL. Then press “Exit” on the Tech 2, switch it off and disconnect it from the vehicle.

Step 3: Data exchange

*   Connect Tech 2 to the pc, switch it on, and click on ‘Next’ on the pc.
*   Confirm VIN or, if necessary, enter correct VIN, then select ‘Next’.

Tech2-program-ecu-with-sps-in-tis2000-3

*   Validate vehicle data and, if necessary, change with the pull-down menus.
*   Click on ‘Next’. Button

Tech2-program-ecu-with-sps-in-tis2000-4

*   A new window displays a “Summary” (follow below) with the selected data. Continue with ‘Next’. Select “Reprog” button to download the latest calibration data onto the TechII diagnostic tool.

Note: It is not possible to reprogram an ECU with the same software version.

Tech2-program-ecu-with-sps-in-tis2000-5

*   The window ‘Transfer Data’ is displayed. A bar shows the progress of the download.

At the end of the download, a window is displayed with the request to connect the Tech 2 to the vehicle in order to finish the programming process.

Tech2-program-ecu-with-sps-in-tis2000-6

*   After the closing of the SPS application the TIS 2000 start screen is again displayed. Finally, switch off the Tech 2 and disconnect it from the pc.

Step 4: Program ECU

*   Connect Tech 2 to the vehicle.
*   Switch on Tech 2 – start screen appears.
*   Turn ignition (Do not start motor!).
*   Press “Enter” in the Tech 2 start screen.
*   Select “F1: Service Programming System” in the main menu and then “F1: Program ECU”.
*   Follow the instructions on the Tech 2 screen.
*   During the download the Tech 2 screen shows the message “Programming in Progress”.
*   At the end of the download the Tech 2 shows the message “Programming was successful”. The button “Exit” leaves the program. First, turn off the ignition of the vehicle, then switch off the Tech 2 and disconnect it from the vehicle.
*   Turn off ignition for 30 seconds before starting the motor. Additional information is available in the section “Check programming”.

Alternative Programming with “Pass Thru”

In addition to the procedure described above, there is an alternative programming mode called “Pass Thru”. In that case, the data are directly downloaded from the pc to the ECU in the vehicle.

Although the Tech 2 is still needed in that mode, the data entry and the download control is done directly at the pc. Altogether, that method is faster, and it is recommended when a pc with TIS 2000 is within 3m of the vehicle.

*   Connect Tech 2 to the vehicle.
*   Connect Tech 2 to the PC switch on Tech 2.
*   Start TIS 2000 on the PC.
*   Select the icon ‘Service Programming System’ (Fig. 1) on the TIS 2000 start page.
*   Start TIS 2000 on the PC.
*   On the screen ‘Select Diagnostic Tool and Programming Process’ (See picture below) make a selection for

***Pass-Thru mode

***the reprogramming of an ECU that was not exchanged or the replacement/programming of a new ECU

***the ECU location.

Then clock ‘Next’ button.

Tech2-program-ecu-with-sps-in-tis2000-7

Check programming result

After every repgrogramming of an ECU a test to check the successful programming has to perform as follows:

*   turn off ignition
*   wait for at least 30 seconds
*   start motor to confirm the successful programming
*   If the motor doesn’t start this points at an error. After the replacement of an ECU it has to be made sure that the necessary programming of the immobilizer was successful.