Search site

Contact

Car diagnostic tools information by obd2tool

https://www.obd2tool.com

Welcome to my blog,here some auto diagnostic tools will be displayed. If you want to know more information,you can visit our official website: www.obd2tool.com.

lovelily750@gmail.com

News

Visitors notice

12/01/2014 07:47
Let your visitors know about news and events on your website as often as possible. You need to keep your website up-to-date so that your visitors will get used to visiting your pages regularly. You can use RSS feeds to deliver new articles directly to your readers.

Website launched

12/01/2014 07:46
Our new website has been launched today. Tell your visitors why you have started a new presentation and how it benefits them. Mention your goals and project advantages. Try to briefly give your visitors reasons why they should return to your pages.

The blog of OBD2 TOOL

How to Restore X431 V X-431 Pro to Factory Settings

03/12/2021 17:34
How to Restore X431 V X-431 Pro to Factory Settings ? Read this before operation: 1. The following method does not apply to X431 V+ and X431 Pro3 2. Please use this function carefully, improper operation may cause the dead of X431 V, besides, after the factory settings are restored, all user...

How to Use HP Tuners vs. Y2K Silverado LM7 & TSP Peformance Cam

03/05/2021 10:08
To begin this HP Tuners Thread… The FIRST Place I went directly to was THIS Site: HPTuners – Connect > Read > Edit > Write > Drive HP Tuners, the home of VCM Suite and the MPVI since 2003. Now enhancing these to new heights with a new feature rich VCM Editor and VCM Scanner, coupled...

How to Use Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007

02/20/2021 18:27
I am gonna use the new tool Xhorse VVDI Key Tool Plus Pad to program a key for Mazda CX-7 2007. The scanner just came to me last week. Xhorse VVDI Key Tool Plus supports DOIP/CAN-FD/ CAN and K protocol switch pin/Chip pin detection/Toyota smart key programming without simulator/Long distance IMMO...

Reset Steering angle sensor via X431 PRO for Buick New Lacrosse

02/20/2021 18:14
This instruction show you guide on how to reset steering angle sensor by X431 PRO. If you want to know more about X431, please click here: How to use launch X431. Steps: Connect X431 interface to Buick New Lacrosse obd port, then run X431 soft. After enter into ESP system,Read 6 error code: U0073...

How to Use Volvo PTT to Diagnose Volvo FM440 Truck

02/11/2021 18:36
This instruction show you guide on how to use Volvo PTT to diagnose engine performance for Volvo FM440 truck. Preparations: How to Download,Install and Activate Volvo Premium Tech Tool PTT 2.7.98? Diagnose Volvo FM440 Truck Engine Performance by Volvo PTT: Connect Volvo PTT interface (VOCOM...

Autel MaxiIM508 + XP400 add keys for 2011 BMW M3 CAS3 step by step

02/11/2021 18:34
Adding a 2011 BMW M3 CAS3+ key via Autel MaxiIM508 W/XP400. had to updated the cas3 module first then do procedure to add a new blank OEM Key. Key has OEM internals with aftermarket case.\ Question: Have Autel MaxiIM608 (=Autel MaxiIM508 + XP400) and doing a CAS3 on the bench today to add key, I...

W124 W212 Xentry star diagnostics Recommend

02/04/2021 13:33
Have a Mercedes W124 2.5d from 1992, W124 2.0 petrol from 1994 and a W212 E350 CDI 10 plate to diagnose, not sure which Xentry Kits to buy, SD Connect C4 is the best. Car model: A Mercedes W124 2.5d from 1992, W124 2.0 petrol from 1994 and a W212 E350 cdi 10 plate. Purpose: I would like to...

ICOM (genuine) Firmware Update Files

02/04/2021 13:23
Hello, guys. I have ICOM Next A (genuine, gray and black) Part Number 81-31-2-360-883. I bought it 2 years ago, so I need a firmware update files for 2020 ISTA+. Bin firmware files that I have with my 2020 ISTA+ HDD  give me a warning “Warning: the image file doesn’t match to the ICOM type” I...

CDA Working With VCI Pod Or Micropod 2

01/06/2021 19:58
What is CDA?  CDA (Chrysler Diagnostic Application) is a powerful dealer tool that allows to make option changes in the VIN. Say for example you have a Chrysler 300, and you go like, gee I would sure like some steering wheel controls, or some dual climate, or some other option! Then you logon...

Autel MK808 Airbag Reset For Porsche

01/06/2021 19:37
Autel MaxiCOM MK808 diagnostic tool supports Porsche module access all available car electronic systems like ABS, SRS(Airbag), Engine, Transmission, Brake Systems and etc. Today, Auteldia.com is gonna show you the newest Autel MK808 Airbag car list for Porsche and the guide to use (to do an...
<< 1 | 2 | 3 | 4 | 5 >>

GM SPS Programming: Tech2 Tool Remote Mode ECU TIS2000 Calibration Update

01/01/2019 21:41

Here is the step-by-step instruction on programming GM (General Motors) ECUs with Tech 2 Scanner and SPS (Service Programming System) application in TIS2000.

NOTE:

Before using the SPS, make sure that the Tech 2 scan tool and the pc contain the latest software, the battery of the vehicle is fully charged, only the ignition is on power, and all cables are connected properly. TIS2000 will not work on 2007 up GM, and software must work together with TIS2000 USB key. If you need to program Saab ECU, you had to use Saab TIS2000 and USB dongle.

Main steps:

Step 1: Instruction for TIS2000 software

Step 2: Data request

Step 3: Data exchange

Step 4: Program ECU

Alternative Programming with “Pass Thru”

Check Programming result

Step 1: Instruction for TIS2000 software

1.Connect the Tech II to the pc.

Note: The hardware key (HWK) has to be registered prior to working with ‘Service Programming System’. To register a hardware key, the form that is enclosed with the hardware key kit has to be filled in and sent to the address at the top. In case the form is missing, the document is also in the TIS 2000 newsletter (see icon in the TIS 2000 tool bar). At first, the user receives a temporary code until the key is registered on the next TIS 2000 CD.

Hardware keys that have already been registered are still valid!

To register the hardware key select ‘Hardware Key Registration’ in the menu ‘Configuration’.

TIS2000 installation video guide
*   Start TIS 2000 on the pc.
*   Select the application ‘Service Programming System’ on the TIS 2000 start page.

Tech2-program-ecu-with-sps-in-tis2000-1

4. On ‘Select Diagnostic Tool and Programming Process’ (picture below) screen make the desired selection for

1) the used Tech2 diagnostic tool

2) the reprogramming of an ECU that was not exchanged or the replacement/programming of a new ECU

3) the ECU location.

Tech2-program-ecu-with-sps-in-tis2000-2

*   Click “Next” button to continue.

Step 2: Data Request

*   Connect Tech 2 scanner to vehicle. Power on device – “Tech 2” is displayed on the screen, then press “ENTER”.

*   Turn ignition to ON without start the engine!!!

*   Select “F1: Service Programming System (SPS)” in the main menu.

*   Press “F0: Request Info” on Tech 2.

*   If Tech 2 has already stored vehicle data they will be displayed now. In that case, Tech 2 asks you to either use the current data (hold data) or request further information from the ECU (continue).

*   For the selection of “Next” the vehicle has to be identified as requested by Tech 2.

Note: Depending on the model year and the selected model either a reprogramming of the ECU (F0: Engine) or of the TCM (F1: Transmission) can be selected.

*   During the Request Info the Professional Diagnostic Tool information from the selected device. If the ECU was replaced a “Request Info” has to be performed for the NEW unit. Since the new ECU is not programmed on delivery, the retrieved information is not complete. For that reason, TIS 2000 gives instructions as how to enter the missing vehicle data.

*   Follow the instructions on the Tech 2 on OBD2TOOL. Then press “Exit” on the Tech 2, switch it off and disconnect it from the vehicle.

Step 3: Data exchange

*   Connect Tech 2 to the pc, switch it on, and click on ‘Next’ on the pc.
*   Confirm VIN or, if necessary, enter correct VIN, then select ‘Next’.

Tech2-program-ecu-with-sps-in-tis2000-3

*   Validate vehicle data and, if necessary, change with the pull-down menus.
*   Click on ‘Next’. Button

Tech2-program-ecu-with-sps-in-tis2000-4

*   A new window displays a “Summary” (follow below) with the selected data. Continue with ‘Next’. Select “Reprog” button to download the latest calibration data onto the TechII diagnostic tool.

Note: It is not possible to reprogram an ECU with the same software version.

Tech2-program-ecu-with-sps-in-tis2000-5

*   The window ‘Transfer Data’ is displayed. A bar shows the progress of the download.

At the end of the download, a window is displayed with the request to connect the Tech 2 to the vehicle in order to finish the programming process.

Tech2-program-ecu-with-sps-in-tis2000-6

*   After the closing of the SPS application the TIS 2000 start screen is again displayed. Finally, switch off the Tech 2 and disconnect it from the pc.

Step 4: Program ECU

*   Connect Tech 2 to the vehicle.
*   Switch on Tech 2 – start screen appears.
*   Turn ignition (Do not start motor!).
*   Press “Enter” in the Tech 2 start screen.
*   Select “F1: Service Programming System” in the main menu and then “F1: Program ECU”.
*   Follow the instructions on the Tech 2 screen.
*   During the download the Tech 2 screen shows the message “Programming in Progress”.
*   At the end of the download the Tech 2 shows the message “Programming was successful”. The button “Exit” leaves the program. First, turn off the ignition of the vehicle, then switch off the Tech 2 and disconnect it from the vehicle.
*   Turn off ignition for 30 seconds before starting the motor. Additional information is available in the section “Check programming”.

Alternative Programming with “Pass Thru”

In addition to the procedure described above, there is an alternative programming mode called “Pass Thru”. In that case, the data are directly downloaded from the pc to the ECU in the vehicle.

Although the Tech 2 is still needed in that mode, the data entry and the download control is done directly at the pc. Altogether, that method is faster, and it is recommended when a pc with TIS 2000 is within 3m of the vehicle.

*   Connect Tech 2 to the vehicle.
*   Connect Tech 2 to the PC switch on Tech 2.
*   Start TIS 2000 on the PC.
*   Select the icon ‘Service Programming System’ (Fig. 1) on the TIS 2000 start page.
*   Start TIS 2000 on the PC.
*   On the screen ‘Select Diagnostic Tool and Programming Process’ (See picture below) make a selection for

***Pass-Thru mode

***the reprogramming of an ECU that was not exchanged or the replacement/programming of a new ECU

***the ECU location.

Then clock ‘Next’ button.

Tech2-program-ecu-with-sps-in-tis2000-7

Check programming result

After every repgrogramming of an ECU a test to check the successful programming has to perform as follows:

*   turn off ignition
*   wait for at least 30 seconds
*   start motor to confirm the successful programming
*   If the motor doesn’t start this points at an error. After the replacement of an ECU it has to be made sure that the necessary programming of the immobilizer was successful.